Course Overview
I have divided this course into four major sections:
Selection of Components: Choosing each component that will be used in the schematic.
Schematic Design: Designing schematics based on datasheet information.
Stack-up and Placement: Planning and executing 4-layer, 6-layer, 8-layer, and 12-layer stack-ups, along with component placement.
Layout Planning: Inter-block and intra-block layout planning and execution.
The major schematic blocks designed in this course include:
Ethernet PHY (10/100 Mb/s)
I2S DAC for headphones and speakers
MEMS microphone
24-bit ADC
36W bi-directional brushed DC motor drivers
UART to USB TTL converter
STM32F103 controller as debugger and programmer
STM32F407 main controller
Power supply and protection circuits
And many more subparts listed in the curriculum.
You will also learn basic blocks such as:
Pre-schematic design: Block diagrams and power budgeting
Rules for stack-up selection and defining stack-ups
Grounding techniques: Signal grounding, earth grounding, chassis grounding
Creating rigid-flex PCBs and their stack-ups
Pin-mapping using Cube-MX tool
Power distribution network (PDN) analysis for PCBs
Selection and application of ferrite beads, ESD diodes, and magnetic components
Placement and layout planning using Microsoft Paint
After completing this course, you will be able to design mixed-signal PCBs with microcontrollers available worldwide.
The major controllers used in this course are:
STM32F407XX
STM32F103XX
Ethernet PHYs, various sensors, ADCs, and DACs
FAQ
FAQ area empty
Course curriculum
Chương 1 Course Details and Selection of Major Components for Complex Mixed Signal Board 9 bài · 2 giờ 4 phút
- Introduction of Section-1 and important instruction Học thử 1:04
- Requirement Sheet Discussion Học thử 7:11
- Selection of Microcontroller and Debugger Học thử 8:56
- Selection of Ethernet PHY Học thử 21:50
- Selection of ADC and TTL Converter Học thử 25:51
-
Selection of Motor Driver 10:42
-
Selection of MOSFET 17:22
-
Selection of DAC MIC and I2S Interface 16:22
-
Block Diagram of Schematic Design Planning 15:07
Chương 2 Schematic Block, Power Budget and Pin Mapping on STM Cube-MX 5 bài · 1 giờ 59 phút
- Introduction of Section-2 and important instruction Học thử 0:55
-
Create Power Budget for Project 18:41
-
Pin Mapping of MCU using Cube-Mx 36:14
-
How to Read Datasheet of STM32F103 26:23
- Schematic Design of STM32F103 Học thử 36:52
Chương 3 Ferrite Bead, ESD, Magnetics Selection and Schematic Design of Ethernet PHY 8 bài · 1 giờ 48 phút
-
Introduction of Section-3 and important instruction 1:05
-
Selection of ESD and TVS diodes 24:46
-
Selection of Magnetics for PHY 5:51
-
Ferrite Bead Selection 14:46
-
Schematic Design for Ethernet PHY Subpart-1 22:13
-
Schematic Design for Ethernet PHY Subpart-2 14:27
-
Schematic Design for Ethernet PHY Subpart-3 13:19
-
IPC STD for Symbol and Footprint 11:33
Chương 4 Schematic Design of Debugger/Programmer in Detail. 7 bài · 1 giờ 59 phút
-
Introduction of Section-4 and important instruction 1:15
-
Schematic Design of Motor Driver Subpart-1 28:31
-
Schematic Design of motor Driver Subpart-2 18:00
-
Bulk Capacitors and Power Supply Selections 15:38
-
UART to TTL Converter Schematic Design 9:50
-
ADC Schematic Design 20:56
-
DAC Schematic Design Subpart-1 25:00
Chương 5 Schematic Design DAC/MIC with Main Controller and Power Supplies for Board 7 bài · 2 giờ 24 phút
-
Introduction of Section-5 and important instruction 1:13
-
Charge Pump DAC and Mems MIC Schematic Design 25:53
-
How to Read the Datasheet of STM32F407 16:29
-
Schematic Design of STM32F407 Subpart-1 40:22
-
Schematic Design of STM32F407 Subpart-2 20:47
-
Power Supplies LDOs Selection and Design 11:22
-
Board Define tools Rigid-Flex PCB and Schematic Templates 27:42
Chương 6 Components Placement for Mixed Signal Board Course 7 bài · 2 giờ 13 phút
-
Introduction of Section-6 and important instruction 1:17
-
Schematic Notes and Footprint Manager before importing Components 23:16
-
Import Components from SCH to PCBDOC and Rooms Discussion 9:35
-
Components Placement Planning on Paints 9:02
-
Components Placement Iteration-1 Subpart-1 31:53
-
Components Placement Iteration-1 Subpart-2 29:28
-
Components Placement Iteration-1 Subpart-3 28:23
Chương 7 Layer Stack-up, Grounding and Earthing Discussion in Detail 5 bài · 1 giờ 34 phút
-
Introduction of Section-7 and important instruction 1:35
-
Layer Stack-up Rules Discussion 4L,6L,8L,12L 24:51
-
Layer Stack-up 2D Field Solver Simulation 17:48
-
Signal GND, Earthing, Chassis GND Discussion 24:52
-
Layer Stack-up Implementation on CAD Tool 25:01
Chương 8 Layout of Mixed Signal Board Part-1 6 bài · 2 giờ 5 phút
-
Introduction of Section-8 and important instruction 0:35
-
Ethernet PHY Block Layout 30:15
-
STM32F103 Block Layout 26:00
-
Regulators and Supply Block Layout 20:14
-
Motor Driver 1 Block Layout 26:30
-
Analog GND, Digital GND and Routing of ADC Block 21:48
Chương 9 Layout of Mixed Signal Board Part-2 4 bài · 2 giờ 19 phút
-
Introduction of Section-9 and important instruction 0:52
-
Types of VIAs and DAC Block Routing 57:28
-
Layout of Motor Driver Block 2 50:21
-
Net-Classes, Colouring of Net, Annotation of Sensitive Nets 30:02
Chương 10 Layout of Mixed Signal Board Part-3 5 bài · 2 giờ 10 phút
-
Introduction of Section-10 and important instruction 0:44
-
Intra-Block Routing Subpart-1 30:39
-
Intra-Block Routing Subpart-2 29:46
-
Intra-Block Routing Subpart-3 29:50
-
Intra-Block Routing Subpart-4 39:22
Chương 11 Bonus Session -Step by Step PDN Analysis of PCB Design 2 bài · 56 phút
-
Introduction of Section-11 and important instruction 1:08
-
Complete PDN Analysis of Complex Mixed Signal Board 54:45
Requirment
-
For this course Student should have "Altium Designer" Installed on their PC / Laptop
-
Student Should have knowledge of Basic Electronics.
-
You do not need any prior knowledge of "Altium Designer" because we'll going to do everything from scratch.
Outcomes
-
How to Extract Components information from Requirement Sheet
-
Selection of Component for Example: Ethernet PHY, Micro-Controller, Motor Driver, Mosfets, ADC, ADC/DAC, MIC etc.
-
How to Draw a Complex Schematic Block and Its Power Budget Diagrams
-
What are Differential pairs, USB2.0, I2Cs, UART/USART, CAN, MII/RMII, I2S and many more interfaces
-
EMI & EMC decisions for a Complex Mixed Signal Schematic Design
-
How to Create Design Rules Decision for Complex Mixed Signal Board
-
Layer Stack-Up Design (4L/6L/8L/12L) and Field Solver Simulation
-
How to Define Board shape and Rigid-Flex PCB Board
-
Components Placement planning for a Complex Board and its Execution
-
How to Layout a Complex Board with more than 10,000 interconnects, and Layout Optimization
-
Power Distribution Network (PDN Analysis) and How to read its Report + Resolve Issues
0 Student
1 Course
0 review